Environmental simulation
Plastics are subject to a variety of environmental influences, such as temperatures, chemicals or sunlight, throughout their entire service life. These influence their performance, their service life and their functionality.
In order to prevent premature failure, we examine the various environmental influences in advance.
Our accredited environmental simulation laboratory offers a variety of standardized and individual tests.
In our accredited laboratory we carry out solar simulation, weathering test, climate test and temperature test. We support our customers in series monitoring, initial sample testing, testing and in the event of damage.
Several xenon chambers, climatic chambers, temperature shock chambers and salt spray chambers are available in our plastics laboratory for processing customer orders.
Range of services: Temperature shock tests for the rapid transfer of test specimens from a lower test temperature to an upper test temperature
Climate tests to simulate changing climatic conditions
Xenon tests for time-accelerated laboratory weathering to simulate damage caused by moisture, full-spectrum sunlight, and high temperatures.
Color measurement to determine the color and gloss effect before and after exposure
Emission measurement as well as the determination of odor behavior
outdoor exposure
Temperature and climate test
Your product is exposed to changing climatic conditions that can occur during its product life? We simulate the influences that can change service life, functionality and properties.
weathering
Weather resistance and durability are in most cases a basic requirement for products and materials that are used outdoors. We offer Florida/Arizona outdoor exposure, UV exposure testing, or cyclic exposure testing.
Solar simulation
Yellowing, fading, clouding or cracking can cause damage both outdoors and indoors. With our xenon test chamber, we can perform time-accelerated laboratory weathering to simulate damage caused by moisture, full-spectrum sunlight, and high temperatures.
emission measurement
In addition to determining the odor behavior, we offer different analysis systems (e.g.: LC-MS, HS-GC-MS & thermal desorption GC-MS) to identify individual substances and to determine their emission behavior under changing environmental conditions, such as different temperatures in a climate chamber.
|
|
Biegeversuch und Schlagbiegeversuch an Dynstat-Probekörpern DIN 53435Dynamischen Schlagbiegeversuch und (quasi-)statischen Biegeversuch an Dynstatproben. Further Informations |
NormDIN 53435 |
Ansprechpartner |
|
|
DIN EN ISO 2039-1: Kugeleindruckversuch an KunststoffenBestimmung der Härte nach DIN EN ISO 2039-1 an Kunststoffen durch Messung der Eindringtiefe einer Stahlkugel in die Oberfläche eines Prüfkörpers unter Einwirkung einer Prüfkraft. Further Informations |
NormDIN EN ISO 2039-1 |
Ansprechpartner |
|
|
Druckversuch an Schaumstoffen: ISO 844Schaumstoffprüfung: Harte Schaumstoffe – Verfahren zur Bestimmung der Druckeigenschaften Further Informations |
NormISO 844 |
Ansprechpartner |
|
|
Druckversuch an Elastomeren: ISO 7743Elastomere oder thermoplastische Elastomere – Bestimmung des Druckverformungs-Verhaltens. Further Informations |
NormISO 7743 |
Ansprechpartner |
|
|
Druckversuch an Kunststoffen DIN EN ISO 604Kunststoffe – Bestimmung von Druckeigenschaften. Ermittlung der Druckfestigkeit, des Druck-E-Moduls und anderer Aspekte. Further Informations |
NormDIN EN ISO 604 |
Ansprechpartner |
|
|
Gelpermeationschromatographie (GPC)Die GPC ist die Methode der Wahl zur Bestimmung der Molmasse und Molmassenverteilung von natürlichen und synthetischen Makromolekülen. Further Informations |
Norm |
Ansprechpartner |
|
|
Kriechstromfestigkeit von KunststoffenVerfahren zur Bestimmung der Prüfzahl und der Vergleichszahl der Kriechwegbildung von festen Isolierstoffen unter der Verwendung von Wechselspannung. Further Informations |
NormDIN EN IEC 60112 |
Ansprechpartner |
|
|
Abrieb von Kautschuk und Elastomeren nach DIN ISO 4649Verfahren zur Bestimmung des Widerstandes von Elastomeren gegen Abrieb. Für vergleichende Prüfungen und Qualitätskontrollen. Further Informations |
NormDIN ISO 4649:2021-06 |
AnsprechpartnerDr. Stefan Loibl stefan[dot]loibl[at]gwp[dot]eu |
|
|
Wärmeformbeständigkeit VICATMethoden zur Bestimmung der thermischen Belastbarkeit von Kunststoffen Further Informations |
NormDIN EN ISO 306 |
AnsprechpartnerDr. Ulrike Rantzsch ulrike[dot]rantzsch[at]gwp[dot]eu |
|
|
UL94-V Prüfungen entsprechend Yellow Card ZertifizierungDie GWP bietet die Prüfungen entsprechend der Yellow Card Zertifizierung nach UL94-V von Kunststoffmaterialien. Further Informations |
NormUL94-V |
AnsprechpartnerDr. Stefan Loibl stefan[dot]loibl[at]gwp[dot]eu |
